Author Topic: New FacePlate  (Read 21286 times)

LarryD

  • Hero Member
  • *****
  • Posts: 975
  • 3DW
Re: New FacePlate
« Reply #30 on: April 07, 2019, 12:15:50 PM »
I wonder how much a new face place costs...  the plate on my #2 has lost a lot of its printing around the rheostat.  :(    I suppose it's technically still under warranty, but is that a warranty item?
------------------------------
See where the Smokin-It Forum Members are located: https://goo.gl/iFgTi1  -- Message me to be added...

old sarge

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 4046
Re: New FacePlate
« Reply #31 on: April 07, 2019, 05:16:28 PM »
Check with Steve.
David from Arizona
US Army 70 - 95
SI 3D & Big Red Controller
CS 066
Lodge Sportsman Grill
Weber Kettle
Ducane Meridian 42 inch Grill
LEM MaxVac 1088A
LEM Big Bite #8 Grinder
Chef's Choice 665 and Rival Slicers
Old Hickory Knives
InstantPot Duo80 Plus

Durangosmoker

  • Hero Member
  • *****
  • Posts: 535
Re: New FacePlate
« Reply #32 on: April 09, 2019, 01:48:34 PM »
I wish the temperature numbers and markers were embossed in the plate, not just silkscreened on.  Mine, too, are getting almost illegible, and I was thinking of either getting a new plate or just using my engraving pen and marking where the settings are (the less pretty option, but easier).
Eric in New York's Hudson Valley, unless I can get out to Durango.
SI #1 in Durango, #2 in NY, and thinking about a 3D.

LarryD

  • Hero Member
  • *****
  • Posts: 975
  • 3DW
Re: New FacePlate
« Reply #33 on: April 09, 2019, 02:24:00 PM »
Check with Steve.

I sent him an email today...  I'll report back on whether it's considered a warranty item.
------------------------------
See where the Smokin-It Forum Members are located: https://goo.gl/iFgTi1  -- Message me to be added...

Lipster

  • Jr. Member
  • **
  • Posts: 41
Re: New FacePlate
« Reply #34 on: April 09, 2019, 07:46:38 PM »
I wish the temperature numbers and markers were embossed in the plate, not just silkscreened on.  Mine, too, are getting almost illegible, and I was thinking of either getting a new plate or just using my engraving pen and marking where the settings are (the less pretty option, but easier).

Patina!

LarryD

  • Hero Member
  • *****
  • Posts: 975
  • 3DW
Re: New FacePlate
« Reply #35 on: April 09, 2019, 08:01:06 PM »
Check with Steve.

I sent him an email today...  I'll report back on whether it's considered a warranty item.

It's apparently covered by the warranty and a new one is being sent to me.  Another example of exemplary support!
------------------------------
See where the Smokin-It Forum Members are located: https://goo.gl/iFgTi1  -- Message me to be added...

old sarge

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 4046
Re: New FacePlate
« Reply #36 on: April 09, 2019, 09:47:16 PM »
This is  what you were looking for?
https://www.smokin-it.com/product-p/fp123.htm
David from Arizona
US Army 70 - 95
SI 3D & Big Red Controller
CS 066
Lodge Sportsman Grill
Weber Kettle
Ducane Meridian 42 inch Grill
LEM MaxVac 1088A
LEM Big Bite #8 Grinder
Chef's Choice 665 and Rival Slicers
Old Hickory Knives
InstantPot Duo80 Plus