Author Topic: Knob Problems  (Read 2087 times)

jmkdae

  • Newbie
  • *
  • Posts: 13
Knob Problems
« on: July 22, 2018, 01:13:41 PM »
My current knob has developed a lot of play.

Question: Is the flat side of the metal stud underneath what I should use point at the temperature? Think of using a straight edge along the flat side extending to the temperature gauge.

Would a new knob help at all?

Thanks
Jim from NW Arkansas
Smokin-it #2

old sarge

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 4046
Re: Knob Problems
« Reply #1 on: July 22, 2018, 05:02:18 PM »
Not familiar with the analog controller but if you can rotate it to its farthest position consistent with the smoker's highest temperature, that should allow you to reposition the knob  and insert a home made shim along the flat to secure the knob/lessen/eliminate the play. You can then order a new knob.  If there is play in the shaft of the controller, you will need a new controller. You might still be covered under the warranty.
David from Arizona
US Army 70 - 95
SI 3D & Big Red Controller
CS 066
Lodge Sportsman Grill
Weber Kettle
Ducane Meridian 42 inch Grill
LEM MaxVac 1088A
LEM Big Bite #8 Grinder
Chef's Choice 665 and Rival Slicers
Old Hickory Knives
InstantPot Duo80 Plus

jmkdae

  • Newbie
  • *
  • Posts: 13
Re: Knob Problems
« Reply #2 on: July 23, 2018, 03:32:23 PM »
An update. Couldn't really play with it too much as I was doing a smoke yesterday.

It does appear that the straight part of the shaft "points" toward the temperature.

I emailed Smokin-it and asked for a replacement.
Jim from NW Arkansas
Smokin-it #2

old sarge

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 4046
Re: Knob Problems
« Reply #3 on: July 23, 2018, 10:14:48 PM »
Sounds good.
David from Arizona
US Army 70 - 95
SI 3D & Big Red Controller
CS 066
Lodge Sportsman Grill
Weber Kettle
Ducane Meridian 42 inch Grill
LEM MaxVac 1088A
LEM Big Bite #8 Grinder
Chef's Choice 665 and Rival Slicers
Old Hickory Knives
InstantPot Duo80 Plus

G man

  • Full Member
  • ***
  • Posts: 84
    • Gordon Radford Photography
Re: Knob Problems
« Reply #4 on: September 20, 2018, 05:44:31 PM »
The knob, (at least on my #2) is by far the weakest link.  I've gone through a couple. 

A quality metal knob or a higher grade plastic knob is definitely needed.
Gordo
50 Miles West of St. Louis, Misery
#2,  and Master Forge Big Green Vertical Charcoal Smoker, (it is now for sale!)

jmkdae

  • Newbie
  • *
  • Posts: 13
Re: Knob Problems
« Reply #5 on: September 21, 2018, 08:44:23 AM »
An update...didn't want to pay $10 for a piece of plastic. Found a nice all metal one at a local electronics store for a buck. Ebay has them as well for about that same price. It's a 0.25 inch shaft.
Jim from NW Arkansas
Smokin-it #2

Lipster

  • Jr. Member
  • **
  • Posts: 41
Re: Knob Problems
« Reply #6 on: September 22, 2018, 11:10:29 PM »
I was at the county landfill today, and they have an area for 'white goods' which is appliances.
Asked if I could grab a couple knobs from some old ranges, and he said no problem, take what you want.  Got some nice 1/4" knobs from an old range which fit perfectly.  Cost was zero.  Just a thought.  I have likely a lifetime supply of spares.